Search Results for ‘engine’

Hey guys so I've got an 02 GTP, the engine is from an 00 GTP and has 185k on it. When I did the swap a year ago I went through and did basically all of the gaskets and seals and did a check on everything including the pistons and what not. Well, this night I got home after a drive and noticed a...

Never used remanufactured L36 3.8 (3800) short block bored standard .020 over. Includes remanufactured heads. Heads have Crow 90lb springs and larger intake valves installed. All work was done by Carolina Machine Engines. Also includes the engine stand (pictured),Felpro engine gasket kit (does...

Hey I have a 1996 Buick Regal Custom Series 2 naturally aspirated 4 door with 107,723 not that it’s relevant. So here’s the issue I bought this car obviously used and the guys mom owned it. Apparently at some point he disconnected the ac somewhere to where nothing but the cabin fan would come on...

So my 2000 GTP I had originally intended to sell ASAP due to various things (lots of rust and the tranny failing) but it seems I’ll have to at least make it last through the North Dakota winter in order to get the money for a nicer one. Pulling the trans through the bottom is not an option for...

I've noticed that when I monitor my timing advance (KR) it's usually around -20 to -25 degrees during normal driving. WOT it'll hit 0 degrees but that's the most I've seen. Is this normal on a stock N/A 3800? The only thing I've really done so far is the ZZP "tune".

Hi guys. New to the form here and just looking for some opinions. Last year, I picked up a 2004 Intimidator SS with 82k miles. This is my fourth 3800 but my first L67 (not counting one i bought to part out.) About a month after I got it, I noticed a very slight ticking noise, mostly on engine...

Here's the story. I bought this car off of my buddy that I have known for years. He was going to scrap it for $200 so he agreed to sell it to me for $250. Down to the meat and potatoes. The biggest problem with the car (other than the power steering is out, different post later) is, while...

I have a set of Remanufactured 3800 heads for sale. They came on a reman engine that I purchased but I had custom heads that I wanted to use. Therefore I dont need these. $400 OBO. Plus shipping. Text 757-359-6407

Hey y'all, My 1988 Electra suffered a piston ejection, and needs a new engine. I've taken junking the car off the table, as it simply holds too much intangible value. The now-dead engine is a Pre-Series 1 3800, n.a. That said, I have access to a Series III n.a. 3800 from a 2006 Pontiac Grand...

Hello everyone, I bought a 1999 Buick Park Avenue, naturally aspirated and, long story short, I replaced the upper plastic intake and gasket hoping that would help my rough idle and low power problem. Upon finishing the repair, and I had borrowed and DTC scanner from a friend and was setting...

The car was great before the accident, two owners,no leaks, transmission responsive and smooth, strong engine 115k, supercharged, the car had no dents or scratches, radiators are damaged, front frame is damaged, engine and transmission still work, car still moves on its own, car is complete...

I have a 2000 regal gs and am in need of a couple things... 3" down pipe. Reprogrammed PCM Cai, or stock airbox. Hi flo cat If you do have something please txt 248 252 4549. Please include brand and price. Thanks Justin

need help with 3800 series 2 swap from 99 olds delta 88 to 2001 monte carlo ss hello i recently bought a 2001 monte carlo ss for $900 in hopes of replacing the old motor, i bought a motor from a 1999 oldsmobile delta 88 that also had a 3800 series II engine, heres my problem, ive checked around...

Hey Everybody, I have a 1998 Buick Regal GS, SC 3.8L. I need to locate the section of engine wiring That plugs into the main harness at the passenger front valve cover and goes to ICM, crank sensor, etc. I also need a section of the ABS harness from the ABS unit on the driver side apron...

Hello I am not sure where to post this problem i am having. I got a 01 firebird with 3800 series 2 v6. Aperantly i got a butsted lower barring. The story behind how THAT! happend is quite ridiculous. Over all i would like to know if i can just pop off the oil tank from the bottom and reach some...

Not sure what is wrong with it. I hired someone from craigslist to fix the piston and it came back still messed up. I put a brand new piston in it with new rings. And I also got new barrings for it. However, It was smoking afterwards. Then he put another block on it and water mixed in with...

3800 SC Supercharged Fiero engine harness for sale Complete plug and play. Fits 85-88 3800 Series II. PCM fits in the stock Fiero ECM location (slight modifications needed) Wired for a 1998-2002 PCM. PCM not included. 4 or 5 Speed Manual Transmission Includes connections for All...

This set was made from a spare 3.8L GM Series II V6 engine and its internals. The coffee table is made from the cast iron block and aluminum oil pan The end table is made from the flywheel, crankshaft, harmonic balancer, and a broke rotor Both include glass table tops coffee table series II...

I have an 03' buick century with the standard 3100 SFI engine. Seens how the 97-05 Buick centurys never came with with the 3800 (to my knowlage). I was wondering if its possible to swap my 3.1L with a 3.8L supercharged engine out of a 97-05 Buick regal. Being more or less the same body style...